Authorized Zanussi dryer service for all models (Condenser and Vented) and capacities (7, 8, 9 kg). Solutions for every fault: not drying, takes too long, overheating, drum not spinning, loud noise, screen not working. Service 16062 open 24/7.
Need Zanussi dryer service? Agent Site provides the unified Zanussi service number 16062 for all Zanussi dryers. Service available for Condenser, Vented, and combination Washer-Dryer models.
We provide Zanussi dryer service for all faults: dryer not drying clothes (code E60), takes too long, excessive heat burning clothes, drum not spinning (code E50), loud noise during rotation, screen not working, humidity sensor not working (code E70), voltage fluctuation (code EH0).
Call 16062 with symptom or code — we'll give you cause and price.
Cycle runs but clothes come out wet or warm but not fully dry.
Most likely causes
What to do
Heating element set after inspection. Thermostat a price set after inspection. Filter cleaning free.
One cycle takes 3-4 hours instead of the normal 1.5-2 hours.
Most likely causes
What to do
Filter and hose cleaning a price set after inspection. Humidity sensor a price set after inspection.
Clothes come out very hot or have burn marks, operational hazard.
Most likely causes
What to do
Safety thermostat a price set after inspection. Vent cleaning a price set after inspection.
You hear the motor but the drum doesn't rotate.
Most likely causes
What to do
Drum belt a price set after inspection. Pulley a price set after inspection. Motor set after inspection.
Friction, knocking, or metallic squealing noises during rotation.
Most likely causes
What to do
Drum bearings set after inspection. Pulley and belt a price set after inspection.
Screen completely off or shows random symbols, device unresponsive.
Most likely causes
What to do
Voltage stabilizer set after inspection. Board replacement set after inspection.
Call Zanussi service 16062 with the code.
| Code | Meaning | Likely cause | Est. cost | Level |
|---|---|---|---|---|
| E50 | Motor or drum fault | Broken belt, burnt motor, worn pulley | set after inspection | Medium |
| E60 | Air heating failure | Burnt heating element or faulty thermostat | set after inspection | Medium |
| E70 | Humidity sensor fault | Faulty or dirty humidity sensor | set after inspection | Low |
| E80 | Drain pump fault (Condenser models) | Jammed or burnt pump | set after inspection | Medium |
| EH0 | Voltage fluctuation | Voltage below 180V or above 250V | set after inspection | Medium |
Motor or drum fault
Broken belt, burnt motor, worn pulley
Air heating failure
Burnt heating element or faulty thermostat
Humidity sensor fault
Faulty or dirty humidity sensor
Drain pump fault (Condenser models)
Jammed or burnt pump
Voltage fluctuation
Voltage below 180V or above 250V
Transparent prices. Inspection fee, included with repair. Call 16062.
⚠️ Pricing notice: All prices listed are estimates only and vary based on the age, type, model, and condition of the device, as well as market fluctuations over time. Prices reflect the current Egyptian market and are updated periodically. The minimum for any visit and repair is set after inspection and extends to a wider range based on the fault. The final exact price is determined after the technician's on-site inspection and before starting.
Simple steps preventing most dryer faults.
Clogged filter causes 80% of dryer faults. Most important tip.
Lint buildup reduces drying efficiency and raises temperature.
Voltage fluctuation burns the electronic board (code EH0).
Overloading shortens belt and bearing life.
8 kg Zanussi dryer stopped drying, code E60 on screen. Technician arrived in 60 minutes, found burnt heating element. Replaced at a price set after inspection. Clothes dry in 1.5 hours.
Zanussi dryer drum stopped (code E50). Was worried about service cost. Called 16062, technician found broken belt. Replaced for just a price set after inspection. Excellent.
Unified Zanussi service number 16062 — instant diagnosis, 1-hour technician, original parts, 6-month warranty.
