Authorized AEG AEG Dryers Service

AEG Dryer Repair - Service Center in Egypt | Call 16062

AEG dryer repair in Egypt for Heat Pump, condenser, thermal dryers and AEG washer-dryer units. We diagnose poor drying, wet clothes, long drying time, no heat, overheating, program stopping early, blocked lint filter, humidity sensor fault, full water tank, water pump fault, dirty condenser, fan issues, loud noise, E60, E70, EHO and PCB faults. Call 16062.

  • Original certified parts
  • 6-month written warranty
  • 1-hour arrival in Cairo
  • AEG-trained specialists
Call Now: 16062 WhatsApp
AEG Dryers
AEG
+15 years
24/7 available
6m warranty

AEG Dryer Repair - Airflow & Moisture Diagnosis Before Parts Replacement

AEG Dryers

If you are looking for AEG dryer service number, the key is choosing a technician who understands that a dryer is not just a heater. AEG dryers rely on airflow, humidity sensor, lint filter, condenser, water pump, fan, temperature sensor, PCB and, in Heat Pump models, a low-temperature drying circuit.

We service AEG Heat Pump dryers, condenser dryers, thermal dryers, AEG washer-dryers and SensiDry, AbsoluteCare, ProSense and ProSteam models depending on the unit. Diagnosis covers filters, airflow path, condenser, humidity sensor, temperature sensor, water pump, water tank, fan, heater, PCB and power supply.

AEG dryer service number: 16062 — poor drying, airflow, humidity sensor, filters, condenser, pump, heater and PCB diagnosis, with final cost after inspection and before repair.
Fault Diagnosis

AEG Dryer Symptoms & Solutions

AEG dryer faults often appear as poor drying, wet clothes, long cycle, water tank warning, loud noise, overheating or display code.

01 AEG dryer not drying clothes Estimated after drying cycle diagnosis Tech needed

Dryer runs and program ends, but clothes come out wet or damp.

Most likely causes

  • 1 Blocked lint filter
  • 2 Dirty condenser
  • 3 Humidity sensor misreading
  • 4 Water pump not working
  • 5 Weak fan
  • 6 Overloading
  • 7 Heater or Heat Pump not efficient

What to do

Diagnosis starts with filters, airflow path, condenser and humidity sensor, then pump, fan and heating circuit.

Estimated cost Estimated after drying cycle diagnosis
02 AEG dryer takes too long Estimated by long-cycle cause Tech needed

Cycle takes too long or keeps extending without good drying.

Most likely causes

  • 1 Blocked lint filter
  • 2 Overload or very heavy clothes
  • 3 Condenser needs cleaning
  • 4 Dirty humidity sensor
  • 5 Weak airflow
  • 6 Heat Pump issue

What to do

Load, filters, condenser and sensors are checked before judging PCB or Heat Pump circuit.

Estimated cost Estimated by long-cycle cause
03 AEG dryer not heating Estimated by heating circuit Specialist

Drum rotates but there is no warm air or clothes temperature does not change.

Most likely causes

  • 1 Faulty heater in thermal dryer
  • 2 Temperature sensor fault
  • 3 Safety thermostat cut-off
  • 4 PCB not sending heat command
  • 5 Heat Pump issue in supported models
  • 6 Voltage instability

What to do

Heater, sensor, thermostat and power are measured before any replacement.

Estimated cost Estimated by heating circuit
04 AEG dryer overheating Estimated after overheating diagnosis Specialist

Appliance gets too hot or clothes come out excessively hot with hot smell.

Most likely causes

  • 1 Blocked lint filter
  • 2 Restricted airflow path
  • 3 Temperature sensor misreading
  • 4 Weak fan
  • 5 Overloading
  • 6 Safety thermostat or PCB

What to do

Stop appliance and check filters, airflow path, sensor and fan, as overheating is risky.

Estimated cost Estimated after overheating diagnosis
05 AEG dryer water tank warning Estimated after pump and tank check Tech needed

Dryer shows water tank warning even after emptying, or stops due to water.

Most likely causes

  • 1 Tank not seated properly
  • 2 Blocked water path
  • 3 Weak water pump
  • 4 Water level sensor
  • 5 Lint or residue blockage

What to do

Tank, water path, pump and sensor are checked before replacing parts.

Estimated cost Estimated after pump and tank check
06 AEG dryer keeps asking to clean filter Estimated by blockage level Tech needed

Clean filter message appears even after cleaning, or dryer only works after repeated cleaning.

Most likely causes

  • 1 Deep internal filter blockage
  • 2 Lint inside airflow path
  • 3 Dirty condenser
  • 4 Airflow sensor
  • 5 Only surface filter cleaning

What to do

Filters are deep-cleaned and airflow path, condenser and airflow sensor are checked.

Estimated cost Estimated by blockage level
07 Loud noise from AEG dryer Estimated after noise source diagnosis Specialist

Rubbing, squeaking, banging or buzzing while drum rotates.

Most likely causes

  • 1 Internal bearing or roller
  • 2 Belt or pulley
  • 3 Foreign object in drum or fan
  • 4 Unbalanced fan
  • 5 Motor or internal mounting

What to do

Noise source is identified: drum, belt, fan, motor or roller before replacement.

Estimated cost Estimated after noise source diagnosis
08 AEG dryer shows E60 Estimated by heating circuit Specialist

Code often related to heating circuit, temperature sensor or insufficient heat.

Most likely causes

  • 1 Heater
  • 2 Temperature sensor
  • 3 Safety thermostat
  • 4 Blocked airflow
  • 5 PCB or wiring

What to do

Airflow is checked first, then heater, sensor and wiring before PCB replacement.

Estimated cost Estimated by heating circuit
09 AEG dryer shows EHO or power issue Estimated after power diagnosis Tech needed

Appliance stops or displays power-supply-related code.

Most likely causes

  • 1 Voltage fluctuation
  • 2 Weak socket
  • 3 Unsuitable extension cord
  • 4 Voltage drop during heating
  • 5 PCB affected by power

What to do

Power source is checked before judging PCB; avoid weak extension cords.

Estimated cost Estimated after power diagnosis
Capacities

We Service All AEG Dryer Types

AEG dryers come in different systems: Heat Pump, condenser, vent/thermal in some models and washer-dryer units. Each type needs a different diagnosis.

Most Popular
Low-temperature drying

AEG Heat Pump Dryer

Fabric care and lower energy use
  • Heat Pump
  • humidity sensor
  • condenser
  • fan
  • PCB
  • filters
Price range Estimated by drying circuit
Most Popular
Water collected in tank

AEG Condenser Dryer

Homes without external vent
  • Condenser
  • water tank
  • pump
  • humidity sensor
  • filters
Price range Estimated after inspection
Direct heating depending on model

AEG Thermal Dryer

Fast drying and classic programs
  • Heater
  • fan
  • temperature sensor
  • safety thermostat
  • lint filter
Price range Estimated by heater and fan
Most Popular
Washing and drying in one unit

AEG Washer Dryer

Space saving at home
  • Drying circuit
  • humidity sensor
  • fan
  • heater
  • drain pump
Price range Estimated by drying system
Most Popular
Gentle fabric drying

AEG SensiDry Dryer

Delicates and daily fabrics
  • SensiDry
  • humidity sensor
  • low temperature
  • PCB
  • filters
Price range Estimated by sensors
Most Popular
Steam and wrinkle reduction

AEG ProSteam Dryer

Refresh and wrinkle reduction
  • Steam
  • temperature sensor
  • humidity sensor
  • PCB
  • water tank
Price range Estimated by steam circuit

Prices are approximate and unofficial. They vary by dryer type, age, filters, condenser, pump, heater, PCB, spare parts availability and repair complexity.

Models

AEG Dryer Models We Service

We service AEG dryers by drying system and fault type. When calling 16062, tell us whether it is a standalone dryer or washer-dryer, Heat Pump or condenser, and whether the problem is poor drying, water tank, noise, heat or displayed code.

Best Seller
AEG Heat Pump Dryer AEG Heat Pump Dryer
Multiple capacities
Heat PumpHumidity sensorCondenserLint filterPCB
Best Seller
AEG 7000 Series AEG 7000 Series Dryer
Depending on model
SensiDryLow-temperature dryingSensorsWater pumpCondenser
Best Seller
AEG 8000 Series AEG 8000 Series Dryer
Advanced technologies
AbsoluteCareHumidity sensorFabric programsPCBFan
Best Seller
AEG Washer Dryer AEG Washer Dryer
Washing and drying
HeaterFanHumidity sensorDrain pumpPCB
Best Seller
AEG ProSteam Dryer AEG ProSteam Dryer
Steam and refresh
SteamWater tankTemperature sensorPCBFilters
Technologies

AEG Dryer Technologies We Repair

AEG dryer repair starts by understanding airflow and moisture cycle. Wet clothes may be caused by blocked lint filter, humidity sensor, dirty condenser, water pump, fan, heater, overloading or PCB.

01

Heat Pump Drying

Heat Pump dries clothes at lower temperatures, protects fabrics and saves energy, but depends on clean airflow, condenser and filters. Blocked filters or dirty condenser weaken drying and extend cycle time.

Benefits
  • Better fabric protection
  • Lower energy use
  • Gentle low-temperature drying
Drawbacks
  • Highly affected by blocked filters
  • Drying gets longer with dirty condenser
Common faults

Poor drying, long cycle, very low heat, wet clothes

02

Humidity Sensor

Humidity sensor detects whether clothes are dry. If dirty or faulty, dryer may stop early while clothes are wet or run too long.

Benefits
  • Drying based on clothes condition
  • Prevents overheating
  • Saves time and energy
Drawbacks
  • Affected by lint and fabric softener residue
  • Wrong reading stops cycle early
Common faults

Clothes come out wet, program stops early, abnormal drying time

03

Lint Filters & Airflow Path

Lint filter is one of the most important dryer parts. Blockage prevents hot airflow, weakens drying, raises heat and may stop the program.

Benefits
  • Stronger airflow
  • Faster drying
  • Protects heater and fan
Drawbacks
  • Neglect causes overheating and poor drying
  • Lint may reach condenser and pump
Common faults

Poor drying, overheating, smell, program stop

04

Fan & Air Circulation

Fan circulates air inside dryer. Weak or stopped fan causes poor heat distribution and wet clothes even if heater or Heat Pump works.

Benefits
  • Better airflow distribution
  • Even drying
  • Less drum moisture
Drawbacks
  • Lint may obstruct fan movement
  • Weak motor causes noise or stop
Common faults

Loud noise, uneven drying, fan not working

05

Water Tank & Condensate Pump

In condenser and Heat Pump dryers, moisture water collects in tank or is pushed by pump. Pump or sensor faults can trigger water tank warning or stop the program.

Benefits
  • Collects clothes moisture
  • Works without external vent
  • Protects from internal water buildup
Drawbacks
  • Blocked water path stops program
  • Pump needs inspection if tank warning repeats
Common faults

Water tank warning, program stop, water not pumped, internal leak

06

Heater & Temperature Sensor

In thermal dryers and washer-dryers, heater and temperature sensor raise air temperature safely. Faults cause no drying, overheating or heating code.

Benefits
  • Faster drying
  • Temperature control
  • Overheat protection
Drawbacks
  • Lint and buildup increase heat load
  • Bad sensor stops cycle
Common faults

No heat, overheating, E60, program stop

07

SensiDry & AbsoluteCare

Fabric-care technologies that reduce heat according to fabric type. Poor drying or clothes shrinkage requires checking sensors, programs and airflow.

Benefits
  • Better fabric care
  • Less shrinkage
  • Programs for different fabric types
Drawbacks
  • Needs accurate humidity and temperature sensors
  • Overloading disturbs program reading
Common faults

Clothes shrinkage, uneven drying, program stop, long cycle

Error Codes

AEG Dryer Error Codes

AEG dryer codes guide the fault area, not direct part replacement. The code guides diagnosis of heat, moisture, pump, filters or power supply.

Code Meaning Likely cause Est. cost Level
E60 Heating or temperature fault Heater, temperature sensor, safety thermostat, airflow blockage, PCB or wiring Estimated after heating circuit diagnosis Medium
E70 Temperature sensor or thermal reading fault Temperature sensor, disconnected wire, abnormal reading or PCB Estimated by sensor and model Medium
E50 Motor or drum rotation fault Motor, belt, pulley, motion sensor or PCB Estimated after rotation diagnosis Critical
E90 / E91 Electronic communication fault PCB, display module, wiring or voltage fluctuation Estimated after PCB and power diagnosis Critical
EHO / Ebo Power supply instability Weak socket, extension cord, voltage drop or PCB protection Estimated after power check Medium
Tank Full Water tank warning Full tank, tank not seated, blocked water path, pump or level sensor Estimated after tank and pump check Medium
Filter Clean filter warning Blocked lint filter, restricted airflow, dirty condenser or airflow sensor Estimated by blockage level Low
Poor Drying Poor drying Filter, condenser, humidity sensor, water pump, fan, overload or Heat Pump Estimated after drying cycle diagnosis Medium
Overheat Overheating Airflow blockage, filter, fan, temperature sensor or safety thermostat Estimated after overheating diagnosis Critical
E60 Medium

Heating or temperature fault

Heater, temperature sensor, safety thermostat, airflow blockage, PCB or wiring

Estimated after heating circuit diagnosis
E70 Medium

Temperature sensor or thermal reading fault

Temperature sensor, disconnected wire, abnormal reading or PCB

Estimated by sensor and model
E50 Critical

Motor or drum rotation fault

Motor, belt, pulley, motion sensor or PCB

Estimated after rotation diagnosis
E90 / E91 Critical

Electronic communication fault

PCB, display module, wiring or voltage fluctuation

Estimated after PCB and power diagnosis
EHO / Ebo Medium

Power supply instability

Weak socket, extension cord, voltage drop or PCB protection

Estimated after power check
Tank Full Medium

Water tank warning

Full tank, tank not seated, blocked water path, pump or level sensor

Estimated after tank and pump check
Filter Low

Clean filter warning

Blocked lint filter, restricted airflow, dirty condenser or airflow sensor

Estimated by blockage level
Poor Drying Medium

Poor drying

Filter, condenser, humidity sensor, water pump, fan, overload or Heat Pump

Estimated after drying cycle diagnosis
Overheat Critical

Overheating

Airflow blockage, filter, fan, temperature sensor or safety thermostat

Estimated after overheating diagnosis
Diagnostic Mode

AEG Dryer Technical Diagnosis

AEG dryer diagnosis starts with airflow and moisture cycle, not only the heater. PCB, heater or pump is not replaced before checking filters, condenser, sensors and airflow path.

How to enter test mode

  1. 1 Identify appliance type: standalone dryer, Heat Pump, condenser or washer-dryer
  2. 2 Read displayed code or warning
  3. 3 Ask if clothes are wet, cycle takes long, filter or tank warning appears
  4. 4 Deep clean lint filter
  5. 5 Check condenser and airflow path
  6. 6 Check humidity and temperature sensors
  7. 7 Check water tank, condensate pump and water path
  8. 8 Check fan and airflow circulation
  9. 9 Check heater or Heat Pump circuit depending on dryer type
  10. 10 Check motor, belt and rotation for noise/no movement
  11. 11 Check power supply before judging PCB

What it tests

1
Lint filter test Checks deep blockage and lint buildup affecting airflow.
2
Condenser test Checks condenser dirt and moisture condensation efficiency.
3
Humidity sensor test Checks whether sensor stops program early or extends it abnormally.
4
Water tank and pump test Checks tank, water path, pump and level sensor.
5
Fan and airflow test Checks fan rotation and lint blockage inside airflow path.
6
Heater and temperature sensor test Measures heating circuit, sensor and thermostat for E60 or no heat.
7
Heat Pump circuit test Checks low-temperature drying circuit in Heat Pump models after excluding filters and condenser.
8
Belt and rotation test Checks drum movement, belt and pulley when noise or no rotation exists.
9
PCB and power test Checks power, wiring and sensors before judging PCB.
Pricing

AEG Dryer Repair & Spare Parts Cost

AEG dryer repair cost varies by appliance type: Heat Pump, condenser, thermal dryer or washer-dryer, and by fault: poor drying, filter, condenser, humidity sensor, water pump, heater, fan, motor, belt, PCB or Heat Pump circuit. Final cost is determined after inspection.

Spare Parts

12
  • AEG Dryer Humidity Sensor For wet clothes or program stopping early
    Estimated by model
  • AEG Dryer Lint Filter For airflow blockage and poor drying
    Estimated by size
  • Dryer Condenser For long drying time or weak condensation
    Estimated by type
  • AEG Condensate Pump For water tank warning or water not pumped
    Estimated after water path check
  • Water Level Sensor For tank warning even after emptying
    Estimated by sensor
  • AEG Dryer Fan For weak airflow, loud noise or uneven drying
    Estimated by fan type
  • AEG Dryer Heater For E60 or no heat
    Estimated by heating circuit
  • Temperature Sensor / Safety Thermostat For overheating or no heating
    Estimated by code
  • Dryer Belt & Pulley For drum not rotating or squeaking noise
    Estimated by model
  • AEG Dryer Motor For drum rotation or motor noise after belt check
    Estimated after full diagnosis
  • AEG Dryer PCB Not replaced before checking sensors and power
    Estimated after inspection
  • Heat Pump Circuit Repair For Heat Pump models with poor drying after filter/condenser checks
    Estimated after specialized diagnosis

Labor & Inspection Fees

  • Technical inspection and fault diagnosis Estimated by area and dryer type
  • Poor drying diagnosis Estimated after filter and condenser check
  • Humidity sensor diagnosis Estimated by sensor and model
  • Water tank and pump diagnosis Estimated after water path check
  • Heater and temperature diagnosis Estimated after heating circuit check
  • Noise and rotation diagnosis Estimated after belt and motor check
  • PCB and power diagnosis Estimated after power and sensors check

⚠️ Listed prices are approximate and unofficial. They may vary depending on fault type, dryer age, filters/condenser condition, spare parts availability and repair complexity. Final cost is confirmed before repair.

Care & Maintenance

AEG Dryer Preventive Maintenance

Advanced AEG dryers need periodic filter and condenser cleaning and correct loading. Most poor drying and long-cycle faults start from lint blockage, overload or full water tank.

Daily

Clean lint filter after every cycle

Accumulated lint weakens airflow, extends drying time and may cause overheating.

Monthly

Check airflow path

If drying suddenly weakens, airflow path or internal filters may be blocked.

Daily

Empty water tank regularly

Full water tank stops program or shows warning even if clothes are not dry.

Monthly

Clean condenser based on usage

Dirty condenser is a major cause of long drying time in condenser and Heat Pump dryers.

Daily

Do not overload the dryer

Overloading blocks airflow between clothes and makes sensor misread.

Daily

Separate fabric types

Mixing heavy towels with light clothes causes uneven drying.

Daily

Avoid weak extension cords

Dryers draw high power, and weak supply may trigger power codes or strain PCB.

Weekly

Do not ignore new noise

A small rubbing or squeaking noise can become belt, roller or fan fault.

Customers

AEG Dryer Repair Reviews

مجفف AEG كان بيطول جداً والملابس تطلع رطبة. الفني فحص الفلاتر والمكثف وحساس الرطوبة وشرح السبب قبل الإصلاح.

مجفف AEG Heat Pump
أحمد عادل التجمع الخامس

كان بيظهر تنبيه خزان المياه رغم إن الخزان فاضي. اتفحصت الطلمبة ومسار المياه واتحل العطل.

مجفف AEG Condenser
منى خالد الشيخ زايد

المجفف كان لا يسخن وظهر كود E60. الفني فحص الفلاتر ومجرى الهواء والسخان والحساس قبل تحديد الإصلاح.

غسالة AEG بمجفف
محمود حسين مدينة نصر

كان فيه صوت عالي مع دوران الحلة. الفني فحص السير والبكر والمروحة وحدد مصدر الصوت بدقة.

مجفف AEG SensiDry
FAQ

FAQs About AEG Dryer Repair

What is AEG dryer service number in Egypt?
AEG dryer service number is 16062. Tell us dryer type and visible fault.
Why is my AEG dryer not drying?
It can be blocked lint filter, dirty condenser, humidity sensor, overload, water pump, fan, heater or Heat Pump circuit.
AEG dryer takes too long — is it normal?
Heat Pump models can be slower, but excessive time or wet clothes indicates filter, condenser, overload or sensor issue.
Water tank warning appears although tank is empty — what should I do?
Usually water path, condensate pump or level sensor. Tank, pump and path are checked first.
AEG dryer not heating — is heater faulty?
Not always. It can be temperature sensor, safety thermostat, airflow blockage, PCB or Heat Pump circuit.
What does E60 mean on AEG dryer?
E60 usually indicates heating or temperature issue. Filters, airflow, heater, sensor, thermostat and PCB are checked.
Why is my AEG dryer overheating?
Overheating is usually blocked lint filter/airflow, weak fan or bad temperature sensor.
Do you repair AEG washer-dryer units?
Yes, we repair AEG washer-dryer units including washing and drying circuits.
How much does AEG dryer repair cost?
AEG dryer repair cost varies by type, fault, age, filters, condenser, pump, heater and PCB. Final cost is confirmed after inspection.
Do you provide AEG customer service or agency repair?
We provide specialized AEG appliance repair service. Call 16062.
Available 24/7

Need AEG Dryer Repair? Call 16062

Looking for AEG dryer repair, AEG service number, customer service, hotline or technician near you? Call 16062. Tell us dryer type and symptom: not drying, wet clothes, long drying time, water tank warning, filter warning, no heat, overheating, loud noise, E60, E70, EHO or Heat Pump issue.

Call: 16062 WhatsApp
1-hour response
6-month warranty
Original parts