Authorized AEG AEG Hoods Service

AEG Hood Repair - Service Center in Egypt | Call 16062

AEG hood repair in Egypt for built-in, chimney, island, decorative and modern kitchen hoods. We diagnose hood not working, weak extraction, cooking smell not removed, loud noise, vibration, motor not spinning, fan failure, lights not working, buttons not responding, touch panel fault, steam/smoke sensor issue, clogged grease filter, carbon filter replacement and ventilation/duct problems. Call 16062.

  • Original certified parts
  • 6-month written warranty
  • 1-hour arrival in Cairo
  • AEG-trained specialists
Call Now: 16062 WhatsApp
AEG Hoods
AEG
+15 years
24/7 available
6m warranty

AEG Hood Repair - Extraction & Ventilation Diagnosis Before Motor Replacement

AEG Hoods

If you are looking for AEG hood service number, the key is choosing a technician who understands the complete extraction system: motor, fan, grease filters, carbon filter, duct or recirculation system, control panel, lighting and sensors.

We service AEG built-in hoods, chimney hoods, island hoods, telescopic hoods, decorative hoods, touch-control hoods and sensor-control models depending on the unit. Diagnosis starts with extraction power, filters, airflow path, motor, fan, speeds, control panel, lights, steam/smoke sensor, power supply and PCB.

AEG hood service number: 16062 — weak extraction, motor, filters, lighting, controls, sensors and duct diagnosis, with final cost after inspection and before repair.
Fault Diagnosis

AEG Hood Symptoms & Solutions

AEG hood faults usually appear as weak extraction, loud noise, motor not working, lights not working, buttons not responding, odor remaining or vibration.

01 AEG hood has weak extraction Estimated after airflow diagnosis Tech needed

Hood runs but steam and odors do not clear quickly, even on highest speed.

Most likely causes

  • 1 Clogged grease filters
  • 2 Saturated carbon filter
  • 3 Narrow or blocked duct
  • 4 Dirty/weak fan
  • 5 Weak motor
  • 6 Wrong installation or too high above cooker

What to do

Diagnosis starts with filters, airflow path, duct and installation height, then motor and fan.

Estimated cost Estimated after airflow diagnosis
02 AEG hood not working at all Estimated after electrical diagnosis Specialist

Hood does not respond to any button; motor and lights do not work.

Most likely causes

  • 1 Power source issue
  • 2 Internal fuse/protection
  • 3 Control panel or touch
  • 4 PCB fault
  • 5 Disconnected internal wiring
  • 6 Motor short

What to do

Power, wiring, fuse and control panel are checked before judging PCB or motor.

Estimated cost Estimated after electrical diagnosis
03 Loud noise from AEG hood Estimated after noise source diagnosis Tech needed

Buzzing, rough, rubbing or vibration noise during operation.

Most likely causes

  • 1 Unbalanced fan
  • 2 Grease buildup on blade
  • 3 Bad motor bearing
  • 4 Loose mounting
  • 5 Narrow duct causing airflow noise
  • 6 Foreign object inside fan

What to do

Noise source is identified: motor, fan, duct or mounting, then cleaned, adjusted or repaired.

Estimated cost Estimated after noise source diagnosis
04 AEG hood motor not spinning Estimated by motor and circuit Specialist

Lights may work but motor does not spin, or buzzing occurs without rotation.

Most likely causes

  • 1 Bad/burnt motor
  • 2 Start capacitor fault in some models
  • 3 Fan stuck by grease
  • 4 PCB not sending command
  • 5 Faulty speed switch
  • 6 Disconnected wiring

What to do

Motor is not replaced directly; fan, capacitor, speeds, PCB and wiring are checked first.

Estimated cost Estimated by motor and circuit
05 AEG hood lights not working Estimated by lighting circuit Tech needed

Hood extracts air but lights do not work, are dim or flicker.

Most likely causes

  • 1 Bad LED lamp
  • 2 Lighting driver
  • 3 Switch or touch fault
  • 4 Disconnected wiring
  • 5 Control PCB
  • 6 Moisture/steam on panel

What to do

Lamp, driver, switch and wiring are checked before judging PCB.

Estimated cost Estimated by lighting circuit
06 AEG hood buttons not responding Estimated after control panel diagnosis Tech needed

Power, speed or light button does not respond, or hood works on one speed only.

Most likely causes

  • 1 Grease/moisture inside control panel
  • 2 Faulty touch panel
  • 3 Bad mechanical switch
  • 4 Control PCB
  • 5 Internal wire/connector
  • 6 Voltage fluctuation

What to do

Control panel, wiring and speeds are cleaned and tested before PCB replacement.

Estimated cost Estimated after control panel diagnosis
07 AEG hood steam sensor not working Estimated by sensor and PCB Tech needed

Auto mode does not increase speed with steam, or speed increases by itself unexpectedly.

Most likely causes

  • 1 Sensor dirty with grease
  • 2 Steam buildup inside panel
  • 3 Sensor fault
  • 4 Control PCB
  • 5 Clogged filters affecting reading

What to do

Sensor and filters are cleaned, sensor reading and PCB checked before replacement.

Estimated cost Estimated by sensor and PCB
08 Cooking smell remains despite hood running Estimated after ventilation diagnosis Tech needed

Hood runs and makes sound, but smells remain or come back.

Most likely causes

  • 1 Expired carbon filter
  • 2 Saturated grease filters
  • 3 Backdraft or blocked duct
  • 4 No make-up air
  • 5 Wrong installation height
  • 6 Recirculation instead of external extraction

What to do

Ventilation type is checked: external duct or recirculation, then filters, duct and installation height.

Estimated cost Estimated after ventilation diagnosis
09 AEG hood vibrates during operation Estimated after mounting diagnosis Tech needed

Noticeable body vibration or rattling sound at high speeds.

Most likely causes

  • 1 Loose mounting
  • 2 Unbalanced fan
  • 3 Grease on blade
  • 4 Loose duct
  • 5 Motor bearing
  • 6 Built-in cabinet pressure/misalignment

What to do

Mounting, fan, duct and installation body are checked before motor replacement.

Estimated cost Estimated after mounting diagnosis
Capacities

We Service All AEG Hood Types

AEG hoods come in different designs: built-in, wall-mounted chimney, island, telescopic and decorative touch/sensor models. Each type needs different diagnosis.

Most Popular
Integrated inside kitchen cabinet

AEG Built-in Hood

Modern kitchens and hidden installation
  • Motor
  • filters
  • control panel
  • duct
  • built-in installation
Price range Estimated by installation and fault
Most Popular
Wall-mounted chimney design

AEG Chimney Hood

Open kitchens and daily cooking
  • Duct
  • motor
  • fan
  • metal filters
  • lighting
Price range Estimated after duct inspection
Most Popular
Above kitchen island

AEG Island Hood

Large and premium kitchens
  • Ceiling mount
  • motor
  • carbon filter
  • duct or recirculation
Price range Estimated by installation and height
Most Popular
Pull-out hidden design

AEG Telescopic Hood

Small kitchens and upper cabinets
  • Sliding rail
  • motor
  • switch
  • filters
  • lighting
Price range Estimated by mechanism
Most Popular
Touch or electronic control

AEG Touch Control Hood

Modern kitchens and precise control
  • Touch panel
  • PCB
  • speeds
  • lights
  • sensor
Price range Estimated by PCB and touch panel
Most Popular
Steam or smoke sensor

AEG Sensor Control Hood

Smart operation by cooking steam
  • Steam sensor
  • PCB
  • auto speeds
  • filters
Price range Estimated by sensors

Prices are approximate and unofficial. They vary by hood type, age, motor, filters, PCB, duct condition, spare parts availability and built-in disassembly complexity.

Models

AEG Hood Models We Service

We service AEG hoods by design, ventilation method and control system. Tell us whether it is built-in, chimney, island, telescopic or touch-control, and whether the issue is extraction, motor, noise, lighting or control panel.

Best Seller
AEG Built-in Hood AEG Built-in Hood
Integrated kitchen cabinet
MotorGrease filtersDuctControl panelLighting
Best Seller
AEG Chimney Hood AEG Chimney Hood
Wall / chimney
ChimneyAir ductMotorMetal filtersLights
Best Seller
AEG Island Hood AEG Island Hood
Ceiling mounted
MountingCarbon filterDuctMotorControl
Best Seller
AEG Telescopic Hood AEG Telescopic Hood
Pull-out design
Sliding railSwitchFiltersMotorLighting
Best Seller
AEG Touch Hood AEG Touch Hood
Electronic control
TouchPCBSpeedsSensorLED lighting
Best Seller
AEG Recirculation Hood AEG Recirculation Hood
Without external duct
Carbon filterGrease filtersMotorInternal pathOdors
Technologies

AEG Hood Technologies We Repair

AEG hood repair starts by understanding extraction, filtration and ventilation. Weak extraction can be caused by grease filter, carbon filter, blocked duct, weak motor, unbalanced fan, speed failure or poor installation.

01

Extraction Power & Airflow

Extraction power depends on motor, fan, filters and duct. If any airflow path is blocked, the hood appears weak even if motor works.

Benefits
  • Better odor and grease removal
  • Protects kitchen cabinets from steam
  • Reduces cooking humidity
Drawbacks
  • Blocked duct or filter greatly reduces extraction
  • Wrong installation weakens performance
Common faults

Weak extraction, remaining odors, steam not removed, speed has no effect

02

Metal Grease Filters

Grease filters capture oil and steam before reaching the motor. Grease buildup causes weak extraction, louder noise and motor strain.

Benefits
  • Protects motor from grease
  • Easy periodic cleaning
  • Improves air quality
Drawbacks
  • Neglect weakens hood
  • Grease buildup causes smell
Common faults

Weak extraction, grease smell, motor noise, grease dripping

03

Carbon Filter & Recirculation

Some AEG hoods work without external duct and use carbon filters for odors. If carbon filter is saturated, air moves but odor remains.

Benefits
  • Suitable for kitchens without duct
  • Reduces odors
  • Easier installation in some cases
Drawbacks
  • Needs periodic replacement
  • Not always as strong as external duct
Common faults

Remaining odors, airflow without odor removal, saturated carbon filter

04

Motor & Fan

Motor is the heart of the hood, fan moves air. Loud noise or vibration often comes from unbalanced fan, motor bearing, grease buildup or loose mounting.

Benefits
  • Strong stable extraction
  • Multiple speeds
  • Better airflow
Drawbacks
  • Grease strains motor
  • Unbalanced fan causes noise and vibration
Common faults

Loud noise, motor not spinning, weak extraction, vibration

05

Hood Speeds & Control Panel

If some speeds do not work or touch panel does not respond, switches/touch panel, PCB and wiring are checked before motor replacement.

Benefits
  • Control by cooking intensity
  • Lower noise at low speeds
  • Stronger operation for frying/grilling
Drawbacks
  • Moisture and grease affect buttons
  • PCB is sensitive to voltage fluctuation
Common faults

Button not working, speed not working, touch not responding, one-speed operation

06

LED Hood Lighting

Hood lighting is important during cooking. If lights fail, cause may be LED lamp, driver, switch, PCB or wiring.

Benefits
  • Better cooking visibility
  • Better kitchen aesthetics
  • Lower power use with LED
Drawbacks
  • Moisture and steam affect wiring
  • Driver may fail with voltage fluctuation
Common faults

Lights not working, dim light, flickering, light button not responding

07

Steam & Smoke Sensor

In some advanced AEG hoods, sensor adjusts speed by steam or smoke. If dirty or faulty, auto speed may not work or run unexpectedly.

Benefits
  • Smart operation by cooking
  • Less manual control
  • Better steam removal when needed
Drawbacks
  • Affected by grease and steam buildup
  • Needs careful cleaning and testing
Common faults

Auto not working, speed increases alone, sensor not responding, unstable extraction

08

Duct & External Ventilation

Duct strongly affects hood performance. Long, narrow, broken or blocked duct reduces extraction and increases noise even if hood is new.

Benefits
  • Direct air exhaust
  • Stronger odor removal
  • Often better than recirculation
Drawbacks
  • Any blockage or break weakens extraction
  • Poor duct increases noise
Common faults

Weak extraction despite motor running, loud airflow, odor return, steam not exhausted

Error Codes

AEG Hood Error Codes & Fault Symptoms

Some electronic AEG hoods may show symbols or warning lights related to filters, sensors or control panel, while most faults appear as weak extraction, loud noise or motor failure.

Code Meaning Likely cause Est. cost Level
Filter Clean filter warning Dirty grease filters, usage counter, saturated carbon filter or airflow sensor Estimated by filter condition Low
Carbon Filter Carbon filter warning Carbon filter needs replacement or reset after replacement Estimated by filter type Low
No Extraction No extraction Motor, fan, blocked duct, filters, PCB or speed fault Estimated after airflow diagnosis Medium
Motor Fault Motor fault Bad motor, stuck fan, start capacitor or power supply Estimated after motor diagnosis Critical
Light Fault Lighting fault LED lamp, driver, switch, PCB or wiring Estimated by lighting circuit Low
Touch Fault Touch panel not responding Touch panel, moisture, grease, PCB or internal wiring Estimated after control panel diagnosis Medium
Auto Sensor Steam sensor or auto mode fault Dirty sensor, blocked filter, PCB or wrong reading Estimated by sensor Medium
High Noise High operating noise Unbalanced fan, motor bearing, mounting, narrow duct or grease Estimated after noise source diagnosis Medium
Weak Extraction Weak extraction Filters, duct, motor, fan, installation height or recirculation system Estimated after ventilation diagnosis Medium
Filter Low

Clean filter warning

Dirty grease filters, usage counter, saturated carbon filter or airflow sensor

Estimated by filter condition
Carbon Filter Low

Carbon filter warning

Carbon filter needs replacement or reset after replacement

Estimated by filter type
No Extraction Medium

No extraction

Motor, fan, blocked duct, filters, PCB or speed fault

Estimated after airflow diagnosis
Motor Fault Critical

Motor fault

Bad motor, stuck fan, start capacitor or power supply

Estimated after motor diagnosis
Light Fault Low

Lighting fault

LED lamp, driver, switch, PCB or wiring

Estimated by lighting circuit
Touch Fault Medium

Touch panel not responding

Touch panel, moisture, grease, PCB or internal wiring

Estimated after control panel diagnosis
Auto Sensor Medium

Steam sensor or auto mode fault

Dirty sensor, blocked filter, PCB or wrong reading

Estimated by sensor
High Noise Medium

High operating noise

Unbalanced fan, motor bearing, mounting, narrow duct or grease

Estimated after noise source diagnosis
Weak Extraction Medium

Weak extraction

Filters, duct, motor, fan, installation height or recirculation system

Estimated after ventilation diagnosis
Diagnostic Mode

AEG Hood Technical Diagnosis

AEG hood diagnosis starts with airflow path and filters, not only motor. Motor or PCB is not replaced before checking filters, duct, fan, speeds, control panel and power supply.

How to enter test mode

  1. 1 Identify hood type: built-in, chimney, island, telescopic or touch-control
  2. 2 Identify ventilation system: external duct or carbon-filter recirculation
  3. 3 Ask whether fault is weak extraction, loud noise, lighting, touch or motor not working
  4. 4 Check grease filters and carbon filter if available
  5. 5 Check duct, airflow path and installation height
  6. 6 Check fan for grease, balance and rubbing
  7. 7 Check motor and speeds
  8. 8 Check control panel, touch and switches
  9. 9 Check lighting, LED circuit and driver
  10. 10 Check steam/smoke sensor in supported models
  11. 11 Check power supply and PCB after excluding simpler causes

What it tests

1
Extraction power test Checks extraction on different speeds and identifies whether weakness comes from filters, duct or motor.
2
Filter test Checks grease filters and carbon filter and their effect on extraction and odors.
3
Duct test Checks duct blockage, narrowness or damage, especially if motor runs but extraction is weak.
4
Motor and fan test Checks motor rotation, fan, balance, noise and capacitor if available.
5
Speed control test Tests each speed to identify switch, PCB or motor fault.
6
Control panel test Checks buttons/touch panel, internal wiring and effects of moisture and grease.
7
Lighting test Checks LED lamps, driver, switch and wiring.
8
Steam sensor test Checks sensor reading, cleaning and wiring in Auto/Sensor Control models.
9
PCB and power test Checks power source, wiring and sensors before judging PCB.
Pricing

AEG Hood Repair & Spare Parts Cost

AEG hood repair cost varies by hood type: built-in, chimney, island, telescopic or touch, and by fault: weak extraction, motor, filters, duct, fan, control panel, lighting, steam sensor or PCB. Final cost is determined after inspection.

Spare Parts

12
  • AEG Hood Motor For motor not spinning or loud noise after fan and power check
    Estimated after motor diagnosis
  • AEG Hood Fan For vibration, weak extraction or unbalanced fan
    Estimated by fan type
  • Metal Grease Filter For blocked filter or damaged metal mesh
    Estimated by size
  • AEG Carbon Filter For recirculation models when odors remain
    Estimated by model
  • AEG Hood Control Panel / Touch For button, touch or speed faults
    Estimated after panel diagnosis
  • AEG Hood PCB Not replaced before checking touch, sensors and power
    Estimated after inspection
  • Hood LED Lights For lights not working or flickering
    Estimated by lighting type
  • LED Driver For dim or flickering lights
    Estimated after circuit check
  • Steam / Smoke Sensor For Auto mode or automatic speed faults
    Estimated by sensor
  • Speed Switch For speed not working or one-speed operation
    Estimated by switch type
  • Filter & Airflow Cleaning For weak extraction, odor and noise caused by grease buildup
    Estimated by grease buildup
  • Hood Duct Inspection / Adjustment For weak extraction despite motor working
    Estimated by duct condition

Labor & Inspection Fees

  • Technical inspection and fault diagnosis Estimated by area and hood type
  • Weak extraction diagnosis Estimated after filter and duct check
  • Motor and fan diagnosis Estimated after noise and rotation check
  • Control panel and touch diagnosis Estimated by panel and model
  • Lighting diagnosis Estimated after LED and driver check
  • Built-in hood disassembly/reinstallation Estimated by kitchen design
  • Island or ceiling-mounted hood diagnosis Estimated by height and installation

⚠️ Listed prices are approximate and unofficial. They may vary depending on fault type, hood age, motor/filter/duct condition, spare parts availability and built-in/island disassembly complexity. Final cost is confirmed before repair.

Care & Maintenance

AEG Hood Preventive Maintenance

AEG hoods need regular filter cleaning and duct checks because grease buildup is the main cause of weak extraction, loud noise and motor strain.

Monthly

Clean grease filters regularly

Grease buildup weakens extraction, increases motor noise and may cause grease dripping.

Yearly

Replace carbon filter when odors remain

If hood uses recirculation, carbon filter has a service life and cleaning alone is not enough.

Daily

Do not always run max speed

Use proper speed for cooking; constant max speed strains motor and increases noise.

Monthly

Check duct when extraction weakens

If filters are clean but extraction is weak, duct or airflow path may be the issue.

Weekly

Do not ignore flickering lights

Flickering may indicate driver, wiring or moisture inside panel.

Daily

Keep control panel dry from steam

Steam and grease on touch/buttons may cause poor response or abnormal operation.

Weekly

Check any new noise quickly

Small rubbing or vibration can become fan or motor fault if ignored.

Monthly

Do not let grease build around fan

Grease on fan blade causes imbalance, loud noise and weak extraction.

Customers

AEG Hood Repair Reviews

شفاط AEG كان شفطه ضعيف رغم إن الموتور شغال. الفني فحص الفلاتر والدكت وطلع السبب انسداد في مسار الهواء.

شفاط AEG مدخنة
أحمد عادل التجمع الخامس

الشفاط كان صوته عالي جداً. الفني فحص المروحة والموتور والتثبيت، واتحل الصوت بعد تنظيف وضبط المروحة.

شفاط AEG بلت إن
منى خالد الشيخ زايد

التاتش كان لا يستجيب أحياناً. الفني فحص لوحة التحكم والتوصيلات ونظف آثار الدهون قبل ما يحدد العطل.

شفاط AEG Touch Control
محمود حسين مدينة نصر

الإضاءة كانت بتقطع والشفط ضعيف. اتفحصت لمبات LED والفلاتر والدرايفر، وتم توضيح التكلفة قبل الإصلاح.

شفاط AEG جزيرة
FAQ

FAQs About AEG Hood Repair

What is AEG hood service number in Egypt?
AEG hood service number is 16062. Tell us hood type and visible fault.
Why is my AEG hood extraction weak?
It may be clogged grease filters, saturated carbon filter, blocked/narrow duct, wrong installation height, dirty fan or weak motor.
AEG hood is loud — is the motor faulty?
Not always. Loud noise can be fan imbalance, grease on blade, loose mounting, narrow duct or foreign object.
AEG hood not working at all — what should I do?
Power source, internal fuse, control panel, wiring, PCB and motor are checked first.
Why are AEG hood lights not working?
It can be LED lamps, driver, switch/touch, wiring or PCB.
Is carbon filter important in AEG hood?
Yes, in recirculation models without external duct, carbon filter reduces odors. When saturated, odor remains.
Touch/buttons not responding — is PCB faulty?
Not necessarily. Grease, moisture, switch, wiring or PCB may be the cause.
Do you repair AEG built-in and island hoods?
Yes, we repair AEG built-in, chimney, island and telescopic hoods with careful disassembly and installation handling.
How much does AEG hood repair cost?
AEG hood repair cost varies by hood type, fault, age, motor, filters, duct, PCB and spare parts.
Do you provide AEG customer service or agency repair?
We provide specialized AEG appliance repair service. Call 16062.
Available 24/7

Need AEG Hood Repair? Call 16062

Looking for AEG hood repair, AEG service number, customer service, hotline or technician near you? Call 16062. Tell us hood type and symptom: weak extraction, loud noise, motor not working, lights not working, touch not responding, speed fault, odor remains, carbon filter, steam sensor or duct issue.

Call: 16062 WhatsApp
1-hour response
6-month warranty
Original parts